A signal cabinet, with its door wide open, reveals that most of the wire has been removed from inside. Done so by Union Pacific, or by scavengers looking for things like copper, it isn't clear. What is clear that none of the existing CTC equipment left on Tennessee Pass will ever be capable of functioning again!
Email Questions or Comments to the Webmaster
or add a comment to the picture.
If, by some miracle, Tennessee Pass was ever put back in service, it would not be with a functioning CTC system. At least, not with the remaining equipment from the original CTC system! As you can see in this picture, this power switch at the east end of Tennessee Pass has been cannibalized. Such is the case with most of the equipment left behind on the pass.
Email Questions or Comments to the Webmaster
or add a comment to the picture.
A look west out of the west end of Tennessee Pass toward the east portal of the tunnel. I found it interesting how many joints there seemed to be on the siding. There may be a little bit of a telephoto compression effect here, but not much. The joints seem to come every 15 or 20 feet long the entire siding.
Email Questions or Comments to the Webmaster
or add a comment to the picture.
Looking west at the west end of Tennessee Pass, there is no longer a signal to tell trains what the condition is departing the block...then again, there aren't any trains either, so I guess the lack of a signal is irrelevant.
Email Questions or Comments to the Webmaster
or add a comment to the picture.
The stamp on this rail indicates that it was made in 1980 at the Colorado Fuel and Iron plant near Pueblo. Other than the significant amount of rust that has accumulated on the rails, the track appears to be in pretty good condition.
Email Questions or Comments to the Webmaster
or add a comment to the picture.
One of the biggest problems caused by the inactivity on Tennessee Pass (as you expect) appears to be rust. Much of the paint on this switch machine is gone, leaving behind a lot of rust.
Email Questions or Comments to the Webmaster
or add a comment to the picture.
An up close look at the "General Railway Signal Co" stamped on to the switch machine located at west Tennessee Pass. Unfortunately, this particular switch machine hasn't had power running to it 15 years!
Email Questions or Comments to the Webmaster
or add a comment to the picture.
Powered switches in CTC territory can be placed into "hand throw" if necessary so the switch can be thrown by hand. This may happen due to a power outage (although rare) or, more likely, because a maintainer is working on the switch and needs to throw it without the dispatcher. This is a closeup view of the hand throw lever on the switch machine.
Email Questions or Comments to the Webmaster
or add a comment to the picture.
The west switch of Tennessee Pass siding was located very close to the east portal of the tunnel at the summit. As you can see in the picture, the signal for eastbound was positioned is such a way that trains coming through the tunnel could have a clear look at the condition of the signal.
Email Questions or Comments to the Webmaster
or add a comment to the picture.
All of Rio Grande's signalling equipment was manufactured by General Railway Signal Company, one of two major players in the signals and CTC market up to this day. The other is Union Switch and Signal which, since 2009, is known as Ansaldo STS.
Email Questions or Comments to the Webmaster
or add a comment to the picture.
A detailed shot of the General Electric logo on the signal control box at the west end of Tennessee Pass.
Email Questions or Comments to the Webmaster
or add a comment to the picture.
While the line itself technically isn't abandoned, the CTC system absolutely is. A look inside the signal cabinet at west Tennessee Pass reveals cut wires and broken glass everywhere. If Tennessee Pass ever were to become active again with CTC, a completely new CTC system would have to be installed.
Email Questions or Comments to the Webmaster
or add a comment to the picture.
It would appear the the signal control box at the west switch of Tennessee Pass has moved around a bit over the course of its life. You can pretty clearly see "Arvada" painted over on the box. And, if you look even closer, it appears "Arvada" was painted over something that starts with a "P". Even closer examination reveals what appears to be an "A" and an "L". That being the case would mean this box also spent time at Palisade near Grand Junction.
Email Questions or Comments to the Webmaster
or add a comment to the picture.
This is the sight eastbound trains would see as they emerged from the Tennessee Pass tunnel at the summit. Well, okay...almost the sight they'd see. Assuming all the masts in the shot actually had their signal heads!
Email Questions or Comments to the Webmaster
or add a comment to the picture.
This is one of the saddest sights I saw the entire day during the visit to Tennessee Pass! Over the years, UP has been cannibalizing the CTC system on the pass to use the components in other areas. Case-in-point would be the missing signal head from the signal at west Tennessee Pass. The best indication a train could get here is now "where-is-the-signal-head-over-yellow".
Email Questions or Comments to the Webmaster
or add a comment to the picture.